Drift Tengoku — November 2006

Drag a corner or click a page to turn it

An archive project by Flock MFGNew issue alerts →

/ 284

About this issue

Bonnet design and modification take center stage, with carbon and FRP options, cooling comparisons, ducting, fitment, and DIY work. Other features cover a rear-wheel-drive GC8 Impreza conversion, Japanese drift builds, and American 240SX, RX-7, and 350Z projects.

Browse all magazines

Page 15 — English draft translation

19.

1. Lowers the car without awkward geometry and corrects the roll center. 2. Steering lock increases 1.5 times, without going over center. 3. Zero Ackermann angle stabilizes full countersteer. With the standard setup, the initial flick feels like throwing the car: the entry determines the result. The AR upright leaves more freedom after initiation and improves the success rate. With little Ackermann angle, there is still room to work at full countersteer— [continued]

24.

Offering this kind of part commercially rather than as a one-off requires confidence in accuracy and strength. “It survives that much D1 use. The standard knuckle can crack or break, but at worst this one bends. That is safer, right?” says maker . He is a craftsman with a long history of building formula-car chassis and expertise in fabrication, and offers many parts for AE86s and older cars. [The safety claim is the quoted developer’s historical statement.]

31.

The left and right wheels normally turn at slightly different angles. Setting that relationship, Ackermann angle, to zero makes both turn by the same amount and reduces the tendency to catch at full countersteer. Is that getting complicated? SP-TEC’s maker says it is such a specialist part that he cannot sell it to someone who does not understand how its differences from standard affect suspension movement. It takes work and costs a little more, but the effect from one part may make it surprisingly good value. Three commercial versions: the AR upright is clearly for experienced drivers. Corrected geometry has benefits, but zero Ackermann makes steering feel very different. Most obviously, self-steering is greatly reduced while contact feel at countersteer increases. Some drivers will consider that an advantage; others may find it too unfamiliar. Yoshioka says he initially struggled with understeer and could not keep up with the car’s reactions. SP-TEC therefore offers three Ackermann arrangements: the zero-angle racing version shown, a semi-racing version with a small angle, and a street version similar to standard. Some may find the change hard to understand or expensive. Others will be eager to get exactly the part they have been waiting for.

Captions and page details
16.

Developer

2.

The spindle/axle position is raised by 50 mm, so swapping the part lowers ride height by 50 mm. The arm mounting points are also optimized for that height. The steering arm is very short too [terminology follows the article’s description].

3.

Installation also requires modifying related parts. The steering stop must be cut, and the tie-rod locking pin cannot be fitted, so do not omit the alternative locking arrangement . On some cars a bracket may interfere and need cutting. Dedicated tie rods are supplied.

5.

Rear ride height drops by 5 mm. The section that often breaks on the original looks stronger. Arm mounting position is corrected by 35 mm. Bushings are not included [final instruction damaged].

6.

At the rear it is almost entirely bolt-on.

11.

Low ride height +

10.

We reconsidered drifting from the ground up!

14.

I cannot compete in D1—

15.

—without this now!

17.

Introduction [fragment]

18.

CULUS

1.

FRONT

4.

Look at the lower-arm angle under normal vehicle weight: it is not pointing upward at all.

8.

REAR

7.

Again, look at the lower-arm angle. It is almost horizontal, suggesting good traction, and the straight driveshaft is not subjected to unnecessary strain .

13.

An owner explains

12.

What makes the AR upright special!

20.

Entering from a straight in third gear with the standard knuckle/upright feels like throwing the car— [continued]

22.

The product itself was reportedly released two years earlier. Cooperation with the D1 JULIUS team and repeated development eventually led to a street version .

23.

—you know. [Continuation]

26.

At first I was not used to it. Without Ackermann angle there are times when understeer becomes strong— [continued]

25.

—there were moments of strong understeer and times when I could not rely on self-steering. It was quite confusing. Everything became quicker, so it felt as though I was reacting too late. I consciously started making all my movements earlier.

29.

Also, after fitting this upright I stopped agonizing over suspension settings and alignment— [continued]

28.

—perhaps because the suspension moves honestly, so there is no need to compensate for it?

30.

A revolutionary suspension modification used on two exceptionally competitive cars— [sentence continues]

32.

13