Drift Tengoku — November 2006

Drag a corner or click a page to turn it

An archive project by Flock MFGNew issue alerts →

/ 284

About this issue

Bonnet design and modification take center stage, with carbon and FRP options, cooling comparisons, ducting, fitment, and DIY work. Other features cover a rear-wheel-drive GC8 Impreza conversion, Japanese drift builds, and American 240SX, RX-7, and 350Z projects.

Browse all magazines

Page 69 — English draft translation

12.

Air entering the adjuster causes softness. The article describes immersing it in engine oil, inserting a thin rod into the center to depress the internal ball, and pumping the tip so air leaves through the side hole. After repeated pumping, a firm tip indicates successful bleeding. If nothing changes, internal sealing may have deteriorated and replacement is suggested. [Historical workshop procedure.]

34.

—adjusters can simply be replaced. A DIY mechanic capable of fitting cams should find it straightforward. Someone using a shop could combine the work with a high-lift cam installation, since extra labor may be limited; healthy adjusters are needed to obtain the cams’ full benefit. Mikami of 3UP says worn adjusters encourage rocker-arm dislodgement and poor high-rpm response. One car sputtered above 6,000 rpm, and investigation found failed adjusters. If a rocker comes off, suspect the adjuster too or it may happen again. Understanding their function helps explain the faults. Rather than merely increasing clearance, deterioration weakens support pressure, allowing the rocker to move excessively and come off. Incorrect valve-opening timing and lift reduce power, making high-lift cams or precise timing adjustment pointless. Learn how they work and care for them. Regular oil maintenance best preserves their health: sludge and foreign matter are enemies, while heavily oxidized oil attacks sealing surfaces. [Technical claims translated from the 2006 feature.]

Captions and page details
1.

Press to assess deterioration

2.

NVCS variable valve timing too [heading damaged]

4.

[Unresolved heading fragment: 意八不]

3.

That ticking noise may come from—

5.

When healthy— [heading fragment]

6.

—deterioration here [component label truncated].

7.

The right-hand example is worn. A healthy one barely moves under finger pressure, almost imperceptibly; the worn one pumps up and down. It cannot hold constant clearance between a rapidly moving rocker and cam. The service manual’s depression limit is .

8.

Bleeding can sometimes restore it!

11.

On SR engines with NVCS it can be difficult to distinguish lash-adjuster noise from noise in the variable-timing mechanism. At 3UP, replacing every lash adjuster once failed to stop the clatter, but replacing the variable-timing unit did. Since then they suspect that unit first. [Shop’s historical experience.]

13.

Timing too [fragment]

16.

The sounds are similar, so they are easy to confuse.

15.

Simple—

14.

How to assess it

18.

Then turn it by hand in the opposite direction. If it turns, the switching mechanism is faulty; if firmly immovable, it is normal. [Procedure context incomplete; linked to the adjacent compressed-air description.]

19.

Applying compressed air to the variable-timing unit’s central hole makes it click toward the [direction wording damaged]—

22.

—it moves [sentence ending].

24.

The forbidden exploded view

20.

Not serviceable by dismantling—

21.

—according to the workshop manual, but…

25.

Removing the crimped plunger-retaining ring revealed a piston, check ball and spring. It resembles a clutch slave cylinder. Loss of sealing in the lower oil chamber lets air enter and causes collapse. Foreign matter and degraded oil can cause this. [Historical teardown explanation.]

26.

Scratches look hazardous here [caption].

29.

Check [label continues with ball].

28.

Ball

27.

Plunger

32.

WW

33.

Sealing here is important

30.

If the hole becomes blocked—

31.

—that looks bad.

38.

042-946-2000

37.

762-5 Minaminagai, Tokorozawa, Saitama

36.

Reporting assistance: 3UP

35.

67