Drift Tengoku — May 1997
An archive project by Flock MFGNew issue alerts →
About this issue
1997 drift-car tests featuring a Skyline GTS25t and Soarer sit alongside an Osaka drift-scene report, driving techniques, troubleshooting and suspension setup. Other features cover an Ebisu Circuit beginner track day, the KAAZ Powerpot LSD and drift-team cars.
Page 31 — English draft translation
Replace it with something stronger! For some reason this trouble is common on S13s and R32/R33s. Perhaps they are not strong enough for drifting—the manufacturer may not have designed for that! A bolt-on factory GT-R part is 2 mm thicker in diameter; GTS-4 and A31 four-wheel-drive models use the same part. Obtain it from a Nissan parts center, dealer or breaker. This swap also requires replacing the tie-rod end, but once done it greatly reduces the likelihood of trouble. Use a tie-rod spacer. [Model text partly damaged]
...is subjected to enormous lateral force, particularly after a long inertia entry. Depending on speed, further forward weight transfer in that situation can snap it in one blow. A common example is braking at full opposite lock after thinking, “I'm going to spin!” If you feel a spin coming, it is better to unwind the steering a little and bring the wheels as close as possible to straight relative to the car.
Captions and page details
How to replace a tie rod
The TROUBLE!!
Stop
Broken tie rod A spare is best, but an emergency repair may allow the car to move If it snaps, you have a serious problem. The straightforward repair is replacement. Because this happens so often, well-prepared drivers—or those accustomed to breaking them—sometimes carry a spare. But what if you have no spare...
ET.
Quick...
1
...lesson
...cannot borrow one and cannot afford a tow? If the break is near the middle, an emergency repair may be possible. Wrap a suitably long wrench or similar object against it with wire as a splint. The article suggests checking gently whether it steers, but stresses that this part experiences greater force than you may imagine...
GC
...can also be removed by hammering. If doing so, do not strike the threaded end directly...
...as this damages the threads. If striking it, loosely fit the nut first...
Replacing the tie-rod end requires a special tie-rod-end puller. Without one, a hammer may be used [continuation in adjacent text]. Striking the side of the end's mounting area as shown can sometimes release it surprisingly easily.
3
2
...so do not push your luck. Universal emergency repair parts used in rallying include a sleeve-like tube that accepts a rod at each end. Carrying one may be useful in an emergency.
...and turn it to separate the tie-rod end from the tie...
Loosen the locknut, then engage a tool on the flats in the center of the tie rod...
...rod.
E
N
U
Preventive tuning
Protect it with a dedicated part! A common explanation for bent S13 tie rods is the lack of a steering stop. Without a knuckle stop on the lower arm to limit steering angle, all tire input while holding full lock is concentrated on the tie rod. Fitting this spacer at the rack end restricts travel to some extent and protects the tie rod.
Factory R32 tie-rod swap
48521-10V06
Part number: tie rod...
Price: ¥2,800
Price [Damaged label]
Price: ¥4,160 Part number: tie rod...
Ikeya Formula 0289-64-5652
Inquiries:
48520-33P26
Price: ¥4,400
...as you know. The steering becoming heavy or pulling severely also shows that the steering system is under abnormal strain. Extremely negative wheel offset and very wide alloy wheels have similar effects. Moderating these settings should naturally reduce tie-rod trouble.
Learn how to spin properly
Keep extreme negative camber moderate
Avoid it through technique When holding as much opposite lock as the steering permits, the tie rod on the turned side is pushed laterally...
Prevent it through setup changes! As everyone knows, extreme negative camber and an excessively low ride height place much more strain on the suspension than standard settings...
29
OPTIeN2