Drift Tengoku — May 1997

Drag a corner or click a page to turn it

An archive project by Flock MFGNew issue alerts →

/ 180

About this issue

1997 drift-car tests featuring a Skyline GTS25t and Soarer sit alongside an Osaka drift-scene report, driving techniques, troubleshooting and suspension setup. Other features cover an Ebisu Circuit beginner track day, the KAAZ Powerpot LSD and drift-team cars.

Browse all magazines

Page 33 — English draft translation

9.

...is the milder case. Unlucky drivers can have all four or five studs break while driving, letting the wheel leave the car. Frankly, that is extremely dangerous. Several causes are possible. First is forgetting to tighten the nuts. You may consider that inexcusable, but frequent hurried tire changes make it surprisingly easy, particularly when nuts are fitted loosely and final tightening is forgotten. At first the car drives normally, but the nuts gradually loosen and movement develops in every direction. Each movement shocks the studs until they snap. Second is weakening through overtightening. Even tiny amounts of excessive tightening stretch a stud. It is not rubber: once stretched, it stays stretched. Keep pulling and it eventually exceeds its strength limit. Repeated tire changes mean repeated tightening and loosening; if a stud is already almost at its breaking point, what happens? A further shock...

11.

Breakage while turning a nut is usually caused by heat-related seizure. Fine-pitch studs such as Nissan's can enter the danger zone after only two or three flat-out circuit laps. It may be best to treat wheel studs as consumables and always carry spares. Drifters perform what amounts to an ordinary driver's lifetime of wheel changes in half a day, so naturally the parts fail faster. That is something we may simply have to accept.

16.

Stick to the specified torque! To avoid wheel-stud trouble, pay attention to tightening force. Neither too loose nor too tight is acceptable. People sometimes tighten with all their strength, which is completely wrong. The article says at least once to experience the specified torque with a torque wrench; most people will find it lighter than imagined. Another point is to keep the threads clean. You need not be obsessive, but check for trapped debris whenever removing a wheel. It also describes lubricant spray or grease as ways to reduce galling and seizure. Small precautions like these are presented as the key to preventing trouble and driving with confidence.

21.

In my case... I've never had one break while driving, but I have broken them changing tires. Immediately after driving, heat can make them seize and snap very easily. Perhaps the only answer is to wait for them to cool somewhat before changing tires. Also, do not overtighten the nuts. I didn't know how tight they should be and tightened too hard, damaging and breaking them. Aftermarket extended studs seem particularly vulnerable. Replacing ordinary spacers with bolt-on wide-track spacers reduced that sort of trouble...

Captions and page details
1.

Repeated tire changes and heat from hard braking clearly put drift-car wheel studs under constant strain. Even so, you would think they would not snap quite so readily...

2.

Neither too loose nor too tight! At a drift track day you almost invariably encounter one or two cars with broken wheel studs. A stud snapping during a tire change...

4.

The TROUBLE!!

3.

Stop

7.

Troubleshooting, Part 4

6.

Drivetrain trouble

5.

“Oh no, I've snapped a wheel stud!”

8.

Broken wheel studs

10.

...snaps it.

14.

... [Damaged short caption]

15.

Spraying lubricant before tightening nuts is described as preventing seizure and galling. Remember to clean dirt away too.

17.

The secret to avoiding trouble

18.

...check it.

19.

...lubricant

22.

Experience

23.

...from experienced drivers

24.

Before tightening the nuts, lubricant...

29.

Tightening with every ounce of strength is not the answer. Overtightening brings harm and no benefit.

12.

Some say extended studs break more easily than factory ones. Nissan's fine thread pitch makes them particularly prone to galling from minor causes...

13.

...so take care.

25.

Front Row: Ryota Yuasa

27.

...for me.

28.

Noriko Shimizu

26.

vivian

31.

OFTION2

30.

31