Drift Tengoku — November 2006

Drag a corner or click a page to turn it

An archive project by Flock MFGNew issue alerts →

/ 284

About this issue

Bonnet design and modification take center stage, with carbon and FRP options, cooling comparisons, ducting, fitment, and DIY work. Other features cover a rear-wheel-drive GC8 Impreza conversion, Japanese drift builds, and American 240SX, RX-7, and 350Z projects.

Browse all magazines

Page 37 — English draft translation

1.

Bonnet modification — fitting a universal duct. Position the duct in the bonnet’s center and provisionally mark the opening. Making the opening slightly larger than the duct allows adjustment during final fitting. Because bonnet distortion and manufacturing variation exist, visual centering may work better than measurement alone. Cut with a grinder or air jigsaw; tin snips can work, but cutting reinforcement takes time. Trim the duct’s mounting flange, leaving about 1 cm: an excessively wide flange creates too much flat area and spoils the finish. Secure the duct with 3M panel adhesive and tapping screws at roughly 10 cm intervals, countersinking them to avoid interfering with the mounting face. Once the adhesive sets, remove the screws and fill the step and holes. First key the bonnet and duct with 80-grit paper. Use fiber filler, high-build filler and finishing filler; sand in sequence with 80-, 120- and 180-grit paper. [Caption text recovered by direct image review; a historical workshop demonstration.]

26.

One-off duct fabrication digest. Mark the duct location; when making an inward-projecting air inlet, check engine-bay clearance or the bonnet may no longer close. Cut the bonnet in a U shape and bend the flap inward. An air jigsaw makes straighter cuts than tin snips. Place a board against the intended fold and tap with a hammer to make a clean bend. Set the duct’s depth. Make its sides from leftover universal-duct material; if unsuitable, use aluminum sheet around 2 mm thick. Join the side pieces and folded bonnet panel with hot glue. Shape the sides and folded areas with fiberglass filler as for the universal-duct installation. To give it an aftermarket look, add raised ribs even though this inlet shape does not need them: make temporary dividers matching the duct, shape fiber filler against them, then remove the dividers after it cures. Use fiber and body filler to finish the shape. Sand three ribs together with abrasive attached to a board to make their heights equal. Add aluminum mesh underneath for appearance, securing it with wiring clips or hot glue. Complete the job by repainting the whole bonnet. Painting only the duct gives a poor finish; after integrating a universal duct or fabricating one, repaint the bonnet for a fresh result.

81.

Distinctive twin ducts! SuperMade FRP Air Duct, ¥20,790; SuperMade, 0725-50-6411. Sold as a left/right pair, their raised shape has presence. Rivets or tapping screws form part of the design, so they also look good without filler. Sized for a Silvia! URAS Erobon Type-1, ¥15,540; URAS, 092-504-5550. Central bonnet fitment, 730 mm upper width × 790 mm lower width × 720 mm length, with fin-like outlets for engine-bay heat. Easy heat release! Kazama FRP Bonnet Duct Type III, ¥13,440; Kazama Auto Service, 048-745-2026. Its smooth curved shape has a larger opening extending to the sides and no central divider. Like Type II, it is intended for central mounting. A clean, flat shape! Kazama FRP Bonnet Duct Type II, ¥13,440; same supplier and telephone. Mounted from underneath to release air after the radiator, it leaves a flat appearance with a thick central divider. Reporting assistance: Japan Craft, 042-590-1196. [Catalog read directly from the image.]

Captions and page details
7.

Universal duct installation digest. This is the fitted item! A large central bonnet duct: URAS Erobon Type-2, ¥15,540. URAS, 092-504-5550. Slightly larger than Type-1, it measures 1,060 mm across the upper edge, 780 mm across the lower edge and 880 mm in length. Its six fin-like ducts release engine-bay heat efficiently.

9.

Installation

18.

URAS

88.

Kazama

91.

048-745-2026

86.

Kazama

93.

URAS

98.

092-504-5550

89.

0725-50-6411

104.

042-590-1196