Drift Tengoku — November 2006

Drag a corner or click a page to turn it

An archive project by Flock MFGNew issue alerts →

/ 284

About this issue

Bonnet design and modification take center stage, with carbon and FRP options, cooling comparisons, ducting, fitment, and DIY work. Other features cover a rear-wheel-drive GC8 Impreza conversion, Japanese drift builds, and American 240SX, RX-7, and 350Z projects.

Browse all magazines

Page 39 — English draft translation

2.

—at Meihan Sportsland, a single 12-minute session pushed coolant above 100°C. I wanted a ducted bonnet, but no aero manufacturer offered one for the C34, so I asked a shop to make bespoke ducts. Afterward, the same driving no longer pushed coolant above °C. The effect surprised me. I like the design as well as the improved cooling, so even if a C34 aftermarket bonnet is released, I do not intend to change it.

18.

I made it four years ago. Aftermarket bonnets were scarce then and individuality was difficult. I wanted a shape nobody else had, obviously recognizable as a duct. Cut an H shape, raise the front and drop the rear. Weld sheet steel into the resulting gaps, then tidy the appearance with filler. Four nearby cars had ducts made this way, but mine had the highest front rise and deepest drop. Cooling improved; coolant fell about 5°C. Changing the horizontal and vertical lengths of the H allows many duct shapes. [Owner’s historical description.]

36.

An FRP ducted bonnet once opened on the expressway, leaving the pins behind! I also had turbo heat ignite the clutch-master reservoir. After these mishaps, I returned to a stock bonnet and made ducts to release radiator airflow and turbo heat. A U-shaped cut alone was hard to bend straight, so I drilled 8 mm holes to make folding easier. Coolant rise is similar to the previous FRP bonnet, and heat shimmer comes out of the turbo duct. I hope the clutch master will no longer burn, and I can drive with peace of mind. [Owner’s historical account.]

Captions and page details
4.

Taniguchi

3.

Laurel

5.

After fitting a GT2540 turbo and high-lift cams, at Mei— [continues in main paragraph]

6.

A wide-open—

7.

—duct—

13.

—works!

17.

Owner

12.

[Isolated linking syllable: に]

8.

Made from sheet steel and filler, the front rises well above the bonnet while the rear drops deeply just before the fan shroud. This lets air that passed through the radiator leave the engine bay.

9.

The bulkhead-side duct also rises like the front one. The reinforcement is cut to make the area flat. It releases engine-bay heat, producing an effect similar to removing the bulkhead rubber seal. [Historical description.]

10.

Release engine-bay heat!

16.

Toshihiro Taniguchi, Minoh, Osaka; Drifter . Other C34 drivers often ask about his bonnet, giving him a chance to show it off. His only complaint: the huge ducts obstruct his view and make it easier to miss clipping points!?

15.

Twin ducts cool well, and I love the looks!

19.

Hasegawa’s 180SX

22.

Limit-Power.net

24.

[Fragment: insert between; context incomplete]

29.

54

28.

19

25.

The duct drops ahead of the fan shroud, so revising its position might improve cooling further. Hasegawa is satisfied because it cools better than having no duct and looks good.

26.

Coolant temperature differs by 5°C!

27.

Owner

31.

Takao Hasegawa, Toyono district, Osaka; Zest . Many 180SX bonnets are now available, including apparently effective cooling designs. He has never seen this duct shape elsewhere, so intends to retain it for its appearance.

32.

—he has a duct— [fragment]

39.

A U-shaped cut allows the bonnet panel to drop between the fan shroud and engine. After an aftermarket bonnet opened unexpectedly, he recognized the need for strength. The design minimizes cuts to the reinforcement while maximizing the duct opening.

38.

Cooling comparable to an aftermarket bonnet!

35.

Just cut and bend—anyone can do it! [Owner’s quote.]

41.

Hidano’s Mark II

30.

An H-shaped cut gives freedom to make the ideal duct!

47.

Around the turbo—

48.

—prevent fires!

46.

Owner

44.

The turbo-heat duct also uses a U-shaped cut folded inward. It sits slightly behind the turbo so heat from the entire turbo can escape.

45.

Shigeru Hidano, Sakai, Osaka; Tinker . Half a year after returning to a factory bonnet, performance is unchanged from the FRP-bonnet days. He emphasizes that the change lets him drive with greater confidence.

50.

37